Check Us Out

 

 

The writer is making a few good observations relating to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround in general in this content below.

Installing a bathtub isn't specifically brain surgery, however it does need solid plumbing, carpentry, and sometimes, tiling skills. Changing an old bath tub with a new one is also a reasonably tough project. If the old bathtub is conveniently easily accessible, the project can relocate immediately; if you have to open a wall surface to eliminate the old bathtub and position the brand-new tub, the task is much harder. In either instance, the task is within a house handyman's skills, although you will require an assistant to move out the old bathtub as well as set in the brand-new one. See to it you have qualified on your own for the task as well as are comfortable trying it. Instead of employing a professional to take control of a halfway-completed project, it is better to take into consideration utilizing one before you start. Possibilities are you may require an expert plumber to make tube connections.
This article will certainly assist you mount a new bath tub in your shower room if you have currently gotten a new bathtub as well as don't require to change the setup of your previous supply of water pipelines.
Your devices and product checklist need to make up the following:

 

• New Bath tub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Flexible Wrench


• Putty Blade


• Screwdriver


• Cold Chisel


• Measuring tape


• Pipe Caps


 

Removing Old Touches

If you need to change old taps with brand-new ones as a part of your installation, after that the first thing you ought to do is separate the supply of water. After doing so, activate the taps to drain pipes any type of water continuing to be in the system. The procedure of eliminating the existing faucets can be quite bothersome due to the limited access that is typically the instance.
Utilize a container wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipes to the faucets. Have a cloth prepared for the continuing to be water that will originate from the pipelines. When the supply pipelines have been eliminated, make use of the same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary faucets from turning during this procedure. As soon as the taps have actually been removed, the holes in the bath/basin will certainly have to be cleaned up of any old securing substance.
Before proceeding to fit the new faucets, contrast the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new taps to fit.

 

 

Suitable New Touches

If the tails of the new faucets are plastic, after that you will need a plastic port to prevent damages to the thread. One end of the port fits on the plastic tail of the faucet as well as the various other end offers a link to the existing supply pipelines.
If you need to fit a monobloc, after that you will need reducing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, position the faucet in the mounting hole in the bath/basin making sure that the washers remain in location in between the tap as well as the sink. Secure the tap in position with the manufacturer supplied backnut. As soon as the tap is safely in position, the supply pipes can be linked to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with typical faucet connectors. The previous kind should be connected to the faucet finishes first, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been linked.

 

 

Mounting the Bath tub

Using the two wood boards under its feet, position the bathtub in the needed setting. The wood boards are helpful in uniformly spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto 4 tiny factors.
The next goal is to guarantee that the bathtub is leveled all round. This can be accomplished by examining the level and changing the feet on the bath tub until the spirit level checks out degree.
To install taps, fit all-time low of the outermost adaptable faucet connector to the proper supply pipeline by making a compression sign up with; then do the exact same for the various other faucet.
Activate the water supply as well as inspect all joints and also brand-new pipework for leaks as well as tighten them if needed. Load the bath tub and also inspect the overflow electrical outlet and also the regular electrical outlet for leaks.
Finally, repair the bathroom paneling as explained in the producer's instruction manual. Tiling as well as sealing around the tub ought to wait until the bathtub has been used at least when as this will certainly resolve it right into its last setting.

 

 

Getting ready for the Setup

First of all, the supporting frame provided with the bathroom must be fitted (if needed) according to the maker's directions. Next, fit the taps or mixer to the bath tub. When fitting the tap block, it is important to make sure that if the faucet includes a plastic washer, it is fitted between the bath and also the faucets. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets unit to prevent pressure on the bath tub.
Fit the versatile tap adapters to the bottom of both taps using 2 nuts and also olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Ensure you use every one of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom must now prepare to be suited its final placement.

 

 

Tiling Around the Tub

In the area where the bathroom satisfies the tile, it is essential to secure the joins with a silicone rubber caulking. This is important as the installation can move sufficient to split a rigid seal, creating the water to permeate the wall surface between the bathroom and the tiling, bring about issues with dampness as well as feasible leakages to the ceiling below.
You can select from a variety of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes as well as cartridges, and can sealing spaces up to a size of 3mm (1/8 inch). If you have a bigger space to load, you can load it with twists of drenched paper or soft rope. Keep in mind to constantly fill up the bath tub with water before securing, to allow for the motion experienced when the tub is in usage. The sealant can split fairly very early if you do not take into account this motion prior to sealing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise easily offered on the marketplace. It is advisable to fit the ceramic tiles making use of waterproof or waterproof adhesive as well as cement.

 

How to Install or Replace a Bathtub

 

Find Your Dimensions

 

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

 

Disconnect the Water Supply and Drain Assembly

 

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

 

Cut Out the Old Tub

 

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

 

Install the New Tub

 

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

 

Secure the Tub

 

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

 

Do you like more info about How to Install a Bathtub? Place a review down below. We would be delighted to hear your thoughts about this blog post. We are looking forward that you visit us again later on. Enjoyed our posting? Please share it. Let someone else check it out. Thank you for going through it.

Book Inspection